Applications
A catalog answers "what can this instrument do". These pages answer "what does this measurement problem need". Each one starts from the situation: the quantity you have to measure, the confidence the result must carry, and the conditions on site. It then says which instrument covers which part, and links to the product specifications and to the technical articles behind them.
Oscillator & Clock Module Production Test
Parallel multi-channel counting, gap-free statistics and data automation: measure frequency, jitter and start-up behavior of every oscillator in a single fixture cycle.
CNT-104S · CNT-102 · CNT-91/91R · TimeView
View the solution
Time & Frequency Reference and Traceability for Calibration Labs
From a GNSS-disciplined rubidium reference and stand-alone high-stability sources to distributing 10 MHz to every bench: building a traceability chain you can explain.
FTR-210R · 6688 / 6689 · FDA-301 · DA-36 · CNT-91/91R
View the solution
Safe Resistance Testing of Igniters, Squibs and Pyrotechnic Devices
Test current never exceeds 8 mA under any fault. When you measure resistance on bridgewires, detonators and explosive bolts, the instrument's safety ceiling matters more than its resolution.
620A-4 · 620UK-V4 · 620A-4R · 630BN · 641RS · 601ES
View the solution
Ballistic Velocity and Chamber Pressure Measurement
From muzzle velocity and downrange time of flight to the pressure-time curve: replace catalog values with measured data and build interior and exterior ballistics capability in the ammunition lab.
Model 35P · Model 36 · Skyscreen III · System 89 · System 88 · System 85
View the solution
Telecom Network Timing: Jitter, Wander and 1-PPS Verification
From raw TIE data to MTIE and TDEV, from verifying a GPSDO's 1-PPS offset to comparing eight sync sources at once: put numbers on network timing problems.
CNT-91/91R · CNT-104S · TimeView · FTR-210R
View the solution
EMC/EMI Near-Field Scanning and Pre-Compliance Testing
The test house only tells you which frequency failed. A near-field scan tells you which component and which trace on the board it is coming from.
SCN series · HRE series
View the solution
Airframe Bonding and Ground Continuity Acceptance Testing
At milliohm bond resistances a two-wire meter mostly reads its own probes. Four-wire Kelvin measurement, test current, checking for stray voltage before you connect, and building an acceptance record that holds up.
620LK-HR · 620LK · 620LK-P5 · 720A · 601ES
View the solution
Radar Test: Target Simulation and Calibration Reflectors
No real targets and no field trips: synthesize range, velocity and RCS echoes electronically, then calibrate the whole radar back with a trihedral reflector of known RCS.
261 Series Standard Gain Horn Antennas · Millimeter-Wave Variable Attenuators · Directional Couplers · 115 / 178 Series Isolators · Low Noise Amplifiers (LNA) · Waveguide-to-Coax Adapters
View the solution
Board-Level Repair and Reverse Engineering for Avionics and Defence Electronics
The OEM has ended support and the schematics are long gone, but the board has another ten years of service ahead. Component-level fault location, schematic recovery and counterfeit screening of spares, all without documentation.
BoardMaster · RevEng · SYSTEM 8 ATM · SYSTEM 8 BFL · SENTRY · ChipMaster Compact Pro
View the solution
In-house Circuit Board Repair for Rail and Heavy Industry
When the control boards in your fleet or your line are obsolete and spares take six months, repairing them yourself is often the only way to keep downtime in check.
BoardMaster External Case · BoardMaster 19" Rack · SYSTEM 8 BFL · SYSTEM 8 MIS 4 · LinearMaster Compact Pro · SYSTEM 8 PPS
View the solutionYour situation not listed? Tell us the quantity you need to measure and the uncertainty you are aiming for, and we will help with the selection.